HOSSFELD UNIVERSAL® BENDERS
HOSSFELD UNIVERSAL® BENDERS
  • HOME
  • BENDERS
    • Tube & Pipe Bender
    • Standard Bender
    • School or Shop Bender
  • HYDRAULICS
  • TOOLING
    • Basic Pipe, Bar, Eye Bolts, Us, Rings
    • Bar and Angle Iron
    • Equalizer Type Pipe and OD Tube Dies
    • Handrail Capping, EMT, Square Tube
    • More Handrail, Square Tube, Angle Iron
    • One Pull Angle Iron, Flat Eye, Diagonal Bends
    • Hydraulic Attachment
  • SUPPORT
    • FAQS
    • TUTORIALS
  • ABOUT
  • CATALOGS
  • STORE
  • GET A QUOTE
  • HOME
  • BENDERS
    • Tube & Pipe Bender
    • Standard Bender
    • School or Shop Bender
  • HYDRAULICS
  • TOOLING
    • Basic Pipe, Bar, Eye Bolts, Us, Rings
    • Bar and Angle Iron
    • Equalizer Type Pipe and OD Tube Dies
    • Handrail Capping, EMT, Square Tube
    • More Handrail, Square Tube, Angle Iron
    • One Pull Angle Iron, Flat Eye, Diagonal Bends
    • Hydraulic Attachment
  • SUPPORT
    • FAQS
    • TUTORIALS
  • ABOUT
  • CATALOGS
  • STORE
  • GET A QUOTE

More Handrail, Square Tube, Angle Iron

All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.
​


Large Radius Bends on Square Tubing
Larger Radius Bends from 8″ inside radius and up on Square Tube up to 1-1/2″ size. (Figure 23-2)
Picture

Bending Rectangular Tube
Feed-Along Type tooling for edgebending Rectangular Tube, 3/4″ x 1-1/2″, 1″ x 1-1/2″ and 1″ x 2″ to 10″ Minimum Inside Radius. (Figure 23-3)
Picture

Edgebending Handrail Capping
4″ Centerline Radius can be done without twisting or distortion (Figure 24). Edgebending Handrail Cap and 1″ x 1/2″ x 1/8″ Channel Combined. Hydraulic attachment and “L” Type Swinging Frame not shown, but is recommended (Figure 24-1). Bending two and three piece Molded Handrail Assembly to larger radius, 10″ and up (Figure 24-2).
Picture
Picture
Picture

Bending Angle Iron Heel Inward
Bend Angle Iron 1/2″ x 1/2″ x 1/8″ through 1-1/2″ x 1-1/2″ x 3/16″ Heel Inward to 10″ or larger radius. (Figure 24-3)
Picture

Bending Angle Iron Heel Outward
Bend Angle Iron 1/2″ x 1/2″ x 1/8″ through 1-1/2″ x 1-1/2″ x 3/16″ Heel Outward to 14″ or larger radius. (Figure 24-4)
Picture
See what you can do with a HOSSFELD BENDER
​​CALL TO ORDER: (507) 452-2182
FAX (507) 454-1194
info@hossfeldbender.com
HOSSFELD MANUFACTURING
1272 Breezy Lane
Winona, MN 55987 ​U.S.A.

​© HOSSFELD MFG LLC. All rights reserved.
Hossfeld Universal® is a registered trademark of Hossfeld Manufacturing LLC.