HOSSFELD UNIVERSAL® BENDERS
HOSSFELD UNIVERSAL® BENDERS
  • HOME
  • BENDERS
    • Tube & Pipe Bender
    • Standard Bender
    • School or Shop Bender
  • HYDRAULICS
  • TOOLING
    • Basic Pipe, Bar, Eye Bolts, Us, Rings
    • Bar and Angle Iron
    • Equalizer Type Pipe and OD Tube Dies
    • Handrail Capping, EMT, Square Tube
    • More Handrail, Square Tube, Angle Iron
    • One Pull Angle Iron, Flat Eye, Diagonal Bends
    • Hydraulic Attachment
  • SUPPORT
    • FAQS
    • TUTORIALS
  • ABOUT
  • CATALOGS
  • STORE
  • GET A QUOTE
  • HOME
  • BENDERS
    • Tube & Pipe Bender
    • Standard Bender
    • School or Shop Bender
  • HYDRAULICS
  • TOOLING
    • Basic Pipe, Bar, Eye Bolts, Us, Rings
    • Bar and Angle Iron
    • Equalizer Type Pipe and OD Tube Dies
    • Handrail Capping, EMT, Square Tube
    • More Handrail, Square Tube, Angle Iron
    • One Pull Angle Iron, Flat Eye, Diagonal Bends
    • Hydraulic Attachment
  • SUPPORT
    • FAQS
    • TUTORIALS
  • ABOUT
  • CATALOGS
  • STORE
  • GET A QUOTE

Handrail Capping, EMT, Square Tube

All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.
​


Bending Handrail Capping
For Cold Bending Handrail Capping up to ½” x 1-3/4” size into Lambs Tongues, Volutes and Edgebends. Edge Bending done with dies shown in Figure 11 (Bending Flat Stock Edgeways). Extra Spacer blocks available for different thicknesses and widths of stock.
  • Bending Lambs Tongue. (Figure 18)
  • Completing Lambs Tongue. (Figure 19)
  • Bending Volute. (Figure 20)
Picture
Picture
Picture

Bending Electro Metallic Tube (EMT), 1/2" to 1-1/4" sizes
Bends 1/2″ to 1-1/4″ sizes EMT on 90 degree Single Pull Dies. Makes full, round, smooth bends without wrinkling because tube is entirely supported from the outside. NO MANDRELS or FILLERS are needed. (Figure 21)
Picture

Bending Electro Metallic Tube (EMT), 1-1/2" to 2" sizes
Bends 1-1/2″ to 2″ sizes on Feed-Along Type Dies. Use of compound leverage principle makes it easy to bend large EMT. Standard radius die for each size furnished. Ideal for making 90 degree bends, 180 degree bends and offsets. (Figure 22)
Picture

Square Tube Bends
Smooth Bends on Square Tubing are easy to make on the HOSSFELD UNIVERSAL® Bender.
​Die sets for bending 1/2″, 3/4″, 7/8″ and 1″ square tubing, 16 gauge through 10 gauge wall, to 3″, 4″, 5″ or 6″ inside radius are available.
  • Square Tube bend using Die Set with Back Block. (Figure 23)
  • Square Tube bend using No. 11B Square Block as Backing Block. (Figure 23-1)
Picture
Picture
See what you can do with a HOSSFELD BENDER
​​CALL TO ORDER: (507) 452-2182
FAX (507) 454-1194
info@hossfeldbender.com
HOSSFELD MANUFACTURING
1272 Breezy Lane
Winona, MN 55987 ​U.S.A.

​© HOSSFELD MFG LLC. All rights reserved.
Hossfeld Universal® is a registered trademark of Hossfeld Manufacturing LLC.