Hossfeld Universal Benders, Hossfeld Bender, Hossfeld Mfg Company
Home  |  About  |  Contact 
Hossfeld Benders Home
Hossfeld Universal Benders, Hossfeld Manufacturing Company, Hossfeld Bender

To order call:
(507) 452-2182

Fax Number
(507) 454-1194

Download Hossfeld Bender catalogs for Model No. 1 and Model No. 2 Benders and parts, Introduction to Tooling, QuickStart Guide

Click to Download
Our Catalogs

 

Largest Variety of Tooling   •   OD Tube   •   Pipe   •   Angle Iron   •   Flat   •   Bar   •   Edgebends   •   Conduit   •   Electro-Magnetic Tube   •   Handrail   •   Scrolls   •   90° Bends   •   180° Bends   •   360° Bends   •   Square Bends   •   Eye-Pins   •   Rings   •   Coils   •   S-Bends   •   U-Bends
Shear Attachment
Punch Attachment
One Pull Inbend Angle Iron Bending
Flat Eye Attachment
Bending Square Tubing on Section Diagonal, 180 Degrees
Bending Square Tubing on Section Diagonal, Feed Along

 

Tooling Options : Shear, Punch, Flat Eye, Diagonal Bends
All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.
Shear attachment for Hossfeld Bender
Shear Attachment
As illustrated above, Shearing is now possible up to 3/8" x 2" flat bar stock, and up to 1/2" round or square bar stock - HOT ROLL MILD STEEL (HRMS) or equivalent. The Standard No. 61B Shear Attachment Complete, comes with set of No. 61B1 Blades, and No. 53B Wrist Pin. (Figure 25)

Back to top

Punch attachment for Hossfeld Standard No. 2 Bender
Punch Attachment
As illustrated above, Punching is possible up to 3/8" diameter hole in 3/8" HOT ROLL MILD STEEL or equivalent. The standard No. 62B Punch Attachment comes with No. 53B Wrist Pin and Coupling Nut. No. 62B1 Round or Square Punch and Dies Sets are available in Sizes 3/16", 1/4", 5/16", 3/8", 7/16", 1/2" and 9/16". (Figure 26)

Back to top

One Pull Inbend Angle Iron Bending tooling for Hossfeld Bender
One Pull Inbend Angle Iron Bending
No. 102B one pull type die set for bending 3/4" x 3/4" x 1/8" through 1-1/4" x 1-1/4" x 1/8" angle iron, flange inward, without wrinkling. 2-3/4", 3" and 3-3/8" radius are available. (Figure 27)

Back to top

Flat Eye Attachment for Hossfeld Bender
Flat Eye Attachment
Attachment for bending eyes on Trailer or Truck Springs as well as other flat stock for heavy hinges, etc. Capacity for Hot Bending, 4-1/2" x 3/8" Spring steel or its equivalent. (Figure 28)

Back to top

Bending Square Tubing on Section Diagonal 180 for Hossfeld Bender
Bending Square Tubing on Section Diagonal 180
Bend Square Tube, 1/2" through 1" on Section Diagonal, 180 Degrees. Radius depends on wall thickness and tube size. (Figure 28-1)

Back to top

Bending Square Tubing on Feed Along
Bending Square Tubing on Feed Along
Bend Square Tube, 1/2" through 1-1/4" on Section Diagonal on 10" or larger radius Feed-Along Type. (Figure 28-2)

Back to top

 
 
Office: (507) 452-2182         Fax: (507) 454-1194         [email protected]

Hossfeld Manufacturing Company 460-462 West Third Street, P.O. Box 557 •  Winona, Minnesota 55987, U.S.A
HOSSFELD UNIVERSAL is a registered trademark of Hossfeld Manufacturing Company

 

Web site design & Hosting : Vision Design Group, Inc.