Hossfeld Universal Benders, Hossfeld Bender, Hossfeld Mfg Company
Home  |  About  |  Contact 
Hossfeld Benders Home
Hossfeld Universal Benders, Hossfeld Manufacturing Company, Hossfeld Bender

To order call:
(507) 452-2182

Fax Number
(507) 454-1194

Download Hossfeld Bender catalogs for Model No. 1 and Model No. 2 Benders and parts, Introduction to Tooling, QuickStart Guide

Click to Download
Our Catalogs

 

Largest Variety of Tooling   •   OD Tube   •   Pipe   •   Angle Iron   •   Flat   •   Bar   •   Edgebends   •   Conduit   •   Electro-Magnetic Tube   •   Handrail   •   Scrolls   •   90° Bends   •   180° Bends   •   360° Bends   •   Square Bends   •   Eye-Pins   •   Rings   •   Coils   •   S-Bends   •   U-Bends
Bending Larger Diameter Rings or Eyes
Bending Round or Square Eyes on Flat Stock
Equalizer Type Pipe and O.D. Tube Dies
90 Degree Bends on Rigid Conduit, Standard Size Pipe
Bending Reinforcing Bar
Bending Scrolls

 

Tooling Options : Equalizer Type Pipe and O.D. Tube Dies
All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.
Figure 1 No 2 bender with tooling needed for bending larger diameter rings or eyes.
Bending Larger Diameter Rings or Eyes
2-1/2" and Larger Eyes or Rings may be made using the 20B1 Cast Cam mounted over the 53B2 center pin. (Figure 12-1)

Back to top

Bending round or square eyes on flat stock
Bending Round or Square Eyes on Flat Stock
The Bulldozer Die illustrated above is designed for making round or square bends on stock up to 3/16" thick and 4-1/2" wide. The advantage of this die for sharp square bends, is that the stock can be easily removed from the machine by pulling a pin; thus round or square eyes can be made. Also, the die is ideal for making intricate bends on wire up to 1/4" diameter. (Figure 13)

Back to top

Equilizer type pipe

OD tube dies

Equalizer Type Pipe and O. D. Tube Dies

For Cold Bending 16 ga. thru 10 ga. O.D. tubing and sch. 40 pipe up to 180 degrees without the use of mandrel or filler. Tube sizes available 3/8" thru 2". Pipe sizes 1/4" thru 2." (Figure 14)

Large Radius Bends or Coils on 3/8" thru 2" O.D. tube and 1/4" thru 2" sch. 40.
(Figure 14-1)

Back to top

90 degree bends on rigid conduit, standard size pipe

90 Degree Bends on Rigid Conduit, Standard Size Pipe

This "Rigid Conduit" bending die is used mainly by electricians for quantity production of 90 degree ells. The capacity on this type of die is 1/2" thru 1-1/2" sch. 40 pipe. (Figure 15)

Back to top

Bending Reinforcing Bars

Bending Reinforcing Bar

Specifically Designed Dies for re-bar sizes though 1" Grade 40 make it easy to bend fill-in mat and saddles as needed on the job. Mounts on bench or rugged steel pedestal available. (Figure 16)

Back to top

Scroll Bending Dies

Bending Scrolls

Scroll Bending Dies form uniform single turn scrolls 2-1/2", 4" and 5" diameter and one-and-one half turn scrolls 6-1/2" and 8" diameter. Hand operated, forms complete scrolls in seconds. Capacity 3/16" x 3/4". (Figure 17)

Back to top

 

 
 
Office: (507) 452-2182         Fax: (507) 454-1194         [email protected]

Hossfeld Manufacturing Company 460-462 West Third Street, P.O. Box 557 •  Winona, Minnesota 55987, U.S.A
HOSSFELD UNIVERSAL is a registered trademark of Hossfeld Manufacturing Company

 

Web site design & Hosting : Vision Design Group, Inc.