Hossfeld Universal Benders, Hossfeld Bender, Hossfeld Mfg Company
Home  |  About  |  Contact 
Hossfeld Benders Home
Hossfeld Universal Benders, Hossfeld Manufacturing Company, Hossfeld Bender

To order call:
(507) 452-2182

Fax Number
(507) 454-1194

Download Hossfeld Bender catalogs for Model No. 1 and Model No. 2 Benders and parts, Introduction to Tooling, QuickStart Guide

Click to Download
Our Catalogs

 

Largest Variety of Tooling   •   OD Tube   •   Pipe   •   Angle Iron   •   Flat   •   Bar   •   Edgebends   •   Conduit   •   Electro-Magnetic Tube   •   Handrail   •   Scrolls   •   90° Bends   •   180° Bends   •   360° Bends   •   Square Bends   •   Eye-Pins   •   Rings   •   Coils   •   S-Bends   •   U-Bends
Bending 1-1/2" and 2" Standard Pipe
180 Degree Bending With Special "L" Frame
Single Stroke 90 Degree Bend on Pipe, Rigid Conduit
Forming Sharp Square Bends On Wide flat Stock

 

Tooling Options : Hydraulic Attachment

The HOSSFELD UNIVERSAL® Hydraulic Attachment is the ONLY hydraulic attachment guaranteed to work with the
HOSSFELD UNIVERSAL® Model No. 2 Bender.

ACCEPT NO IMITATIONS!

The Hossfeld hydraulic attachment is easy to install and operate, ruggedly constructed, economical to use and versatile
EASY TO INSTALL • SIMPLE TO OPERATE
RUGGEDLY CONSTRUCTED

ECONOMICAL TO USE • VERSATILE

Production bending in short runs and hard to pull bends on heavy material are accomplished easily with Hydraulic power provided by the Hydraulic Attachment for the No. 2 HOSSFELD UNIVERSAL® Bender.

Simple, positive foot control of the hydraulic power leaves both hands free to control stock. Double acting cylinder returns swinging frame while operator resets stock for feed along bending. Operator can gauge degree of bend better and complete bends faster, with less work, than by manual bending.

For bending 90 degree up to 180 degree on wrap around type dies a special "L" type swinging frame is available (See Figure 30 illustration).

The Hydraulic Attachment can be used with any Model No. 2 HOSSFELD UNIVERSAL® Bender.  Installation can be made quickly and easily with only 4 bolts (included) by following simple, illustrated instructions furnished. Changing from power to manual operation requires only disconnecting, or connecting, the hydraulic ram by pulling, or inserting, one pin.

Typical bends are illustrated below. With the exception of the bending of eye bolts (Figures 2 and 6), all the bends illustrated on the Tooling pages can be made on the hydraulic powered unit.

Back to top

 

Bending 1-1/2 inch and 2 inch pipe with the hydraulic attachment
Bending 1-1/2" and 2" Standard Pipe
Feed-Along Type Dies permit any degree of bend, offsets, and coils. (Figure 29)

Back to top

 

180 degree bending with special L Frame
180 Degree Bending With Special "L" Frame
Bend pipe, tube or solid stock on wrap around dies. (Figure 30)

Back to top

Single Stroke 90 Degree Bend on pipe, rigid conduit
Single Stroke 90 Degree Bend on Pipe, Rigid Conduit
No Mandrels or Fillers required to make smooth bends. (Figure 31)

Back to top

Forming Sharp Square bends on wide flat stock
Forming Sharp Square Bends On Wide flat Stock
Cold Bend up to 1/4" x 4-1/2" HOT ROLLED MILD STEEL or equivalent. (Figure 32)

Back to top

 
 
Office: (507) 452-2182         Fax: (507) 454-1194         [email protected]

Hossfeld Manufacturing Company 460-462 West Third Street, P.O. Box 557 •  Winona, Minnesota 55987, U.S.A
HOSSFELD UNIVERSAL is a registered trademark of Hossfeld Manufacturing Company

 

Web site design & Hosting : Vision Design Group, Inc.