Hossfeld Universal Benders, Hossfeld Bender, Hossfeld Mfg Company
Home  |  About  |  Contact 
Hossfeld Benders Home
Hossfeld Universal Benders, Hossfeld Manufacturing Company, Hossfeld Bender

To order call:
(507) 452-2182

Fax Number
(507) 454-1194

Download Hossfeld Bender catalogs for Model No. 1 and Model No. 2 Benders and parts, Introduction to Tooling, QuickStart Guide

Click to Download
Our Catalogs

 

Largest Variety of Tooling   •   OD Tube   •   Pipe   •   Angle Iron   •   Flat   •   Bar   •   Edgebends   •   Conduit   •   Electro-Magnetic Tube   •   Handrail   •   Scrolls   •   90° Bends   •   180° Bends   •   360° Bends   •   Square Bends   •   Eye-Pins   •   Rings   •   Coils   •   S-Bends   •   U-Bends
Bending Handrail Capping
Bending Electro Metallic Tube (EMT),
1/2" to 1-1/4" Sizes
Bending Electro Metallic Tube (EMT), 1-1/2" to 2" sizes
Square Tube Bends

 

Tooling Options : Handrail Capping, EMT, Square Tube
All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.

Bending lambs tongue

Completing lambs tongue

Bending volute

Bending Handrail Capping

For Cold Bending Handrail Capping up to ½” x 1-3/4” size into Lambs Tongues, Volutes and Edgebends. Edge Bending done with dies shown in Figure 11 (Bending Flat Stock Edgeways). Extra Spacer blocks available for different thicknesses and widths of stock.

  • Bending Lambs Tongue. (Figure 18)
  • Completing Lambs Tongue. (Figure 19)
  • Bending Volute. (Figure 20)

Back to top

 

Bending electro metallic tube (EMT)
Bending Electro Metallic Tube (EMT), 1/2" to 1-1/4" sizes.
Bends 1/2" to 1-1/4" sizes EMT on 90 degree Single Pull Dies. Makes full, round, smooth bends without wrinkling because tube is entirely supported from the outside. NO MANDRELS or FILLERS are needed. (Figure 21)

Back to top

Bending Electro Metallic Tube (EMT), 1-1/2" to 2 " sizes.
Bending Electro Metallic Tube (EMT), 1-1/2" to 2 " sizes.
Bends 1-1/2" to 2" sizes on Feed-Along Type Dies. Use of compound leverage principle makes it easy to bend large EMT. Standard radius die for each size furnished. Ideal for making 90 degree bends, 180 degree bends and offsets. (Figure 22)

Back to top

Figure1

Square Tube bend using No. 11B Square Block as Backing Block.

Square Tube Bends

Smooth Bends on Square Tubing are easy to make on the HOSSFELD UNIVERSAL® Bender. Die sets for bending 1/2", 3/4", 7/8" and 1" square tubing, 16 gauge through 10 gauge wall, to 3", 4", 5" or 6" inside radius are available.

  • Square Tube bend using Die Set with Back Block. (Figure 23)
  • Square Tube bend using No. 11B Square Block as Backing Block. (Figure 23-1)

Back to top

 
 
Office: (507) 452-2182         Fax: (507) 454-1194         [email protected]

Hossfeld Manufacturing Company 460-462 West Third Street, P.O. Box 557 •  Winona, Minnesota 55987, U.S.A
HOSSFELD UNIVERSAL is a registered trademark of Hossfeld Manufacturing Company

 

Web site design & Hosting : Vision Design Group, Inc.