Hossfeld Universal Benders, Hossfeld Bender, Hossfeld Mfg Company
Home  |  About  |  Contact 
Hossfeld Benders Home
Hossfeld Universal Benders, Hossfeld Manufacturing Company, Hossfeld Bender

To order call:
(507) 452-2182

Fax Number
(507) 454-1194

Download Hossfeld Bender catalogs for Model No. 1 and Model No. 2 Benders and parts, Introduction to Tooling, QuickStart Guide

Click to Download
Our Catalogs

 

Largest Variety of Tooling   •   OD Tube   •   Pipe   •   Angle Iron   •   Flat   •   Bar   •   Edgebends   •   Conduit   •   Electro-Magnetic Tube   •   Handrail   •   Scrolls   •   90° Bends   •   180° Bends   •   360° Bends   •   Square Bends   •   Eye-Pins   •   Rings   •   Coils   •   S-Bends   •   U-Bends
Bending Sharp Bends or "U" Bolts
Bending Ornamental Iron Work
Bending Angle Iron with Flange Inward
Bending Angle Iron with Flange Outward
Bending Flat Stock Edgeways
Bending Notched Angle Iron

 

Tooling Options : Bar and Angle Iron
All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.
Bending sharp bends or "U" bolts
Bending Sharp Bends or "U" Bolts
Sharp Cornered "U" Bolts are bent on the same feature of the bender as shown for bending ornamental iron. This feature is also used for bending short close hooks on the ends of rods. It will bend a hook with sharp inside corners and having an inside spread of as close as 5/8". It has a capacity of 5/8" round or square stock or 3" x 1/4" flat stock, cold. Illustration shows a sharp square bend. (Figure 7)

Back to top

Bending ornamental iron work
Bending Ornamental Iron Work
This feature of the bender is used in making Ornamental Iron shapes and various other intricate bends. Bends a sharp corner and will handle work as small as the making of a staple or a small nail. This feature has a capacity of 3" x 1/4" flat stock or 5/8" round stock, cold. Illustration shows an ornamental iron shape being formed. (Figure 8)

Back to top

Bending angle iron with flange inward
Bending Angle Iron with Flange Inward
Attachments for bending Angle Iron with either the Flange Inward or Flange Outward consist of a Master Die with which forming blocks of various radii can be used. These blocks work on a wedge principle so that when the bending pressure is applied, the horizontal flange of the stock is held in a vise-like grip. This helps prevent crimping or twisting. (Figure 9)

Back to top

Bending angle iron with flange outward
Bending Angle Iron with Flange Outward
Forming Blocks for bending radii of 5, 6, 7, 9, 12, 15, 18, 24, 30, and 36 inches are furnished with Inbend and Outbend Attachments. Blocks for any radius up to 10 ft. (Minimum Inbend: 3", Minimum Outbend: 4") can be furnished if desired. Both Inbend and Outbend Attachments have a capacity of 2" x 2" x 3/16" stock, cold, or 2" x 2" x 3/8" stock, hot. (Figure 10)

Back to top

Bending flat stock edgeways
Bending Flat Stock Edgeways
Bend Edgeways with Edgebend Die used with outbend master die, wrist pin and inner radius block. Size of inner radius block determines radius of bend. Capacity 3/8" x 1-3/4" cold. Bends flat edgeways from 4" inside radius and up to any degree including 360 degree circles. Same setup used for bending hand rail capping edgeways. (Figure 11)

Back to top

Bending notched angle iron
Bending Notched Angle Iron
This feature of the bender is used for bending sharp bends on angle iron after the point of bend has been notched. This feature has a capacity of 2-1/2" x 2-1/2" x 5/16" angle iron stock, cold. This special Die will also form sharp "V" bends on flat stock. (Figure 12)

Back to top

 
 
Office: (507) 452-2182         Fax: (507) 454-1194         [email protected]

Hossfeld Manufacturing Company 460-462 West Third Street, P.O. Box 557 •  Winona, Minnesota 55987, U.S.A
HOSSFELD UNIVERSAL is a registered trademark of Hossfeld Manufacturing Company

 

Web site design & Hosting : Vision Design Group, Inc.