Largest Variety of Tooling   •   OD Tube   •   Pipe   •   Angle Iron   •   Flat   •   Bar   •   Edgebends   •   Conduit   •   Electro-Magnetic Tube   •   Handrail   •   Scrolls   •   90° Bends   •   180° Bends   •   360° Bends   •   Square Bends   •   Eye-Pins   •   Rings   •   Coils   •   S-Bends   •   U-Bends

Basic Pipe, Bar, Eye Bolts, “U”s, Rings

Bending Pipe and Conduit
Bending Eye Bolts, “S” Shapes, Etc.
Bending Angles, Offsets, Etc., of Heavy Cold Stock
Bending Heavy Cold “U” Shapes
Bending Sharp Square Bends on Wide Flat Stock
Bending Rings and Coils

Basic Pipe, Bar, Eye Bolts, “U”s, Rings

All figures show the No. 2 Bender with tooling needed for the specific bend. All tooling sold separately.

Bending pipe and conduit

Bending Pipe and Conduit

Bends Cold, all sizes of standard pipe and conduit up to 2″ inside diameter. Makes a smooth even bend without flattening the pipe or splitting the seam. Bends to any degree or to a continuous coil as desired. Bends to 10 ” radius on the 2″ size, down to a 2″ radius on the 1/4″ size. Illustration shows a 1-1/4″ standard pipe being bent to a return bend on an 8″ radius. (Figure 1)

Back to top

Bending eye bolts, S shapes, etc.

Bending Eye Bolts, “S” Shapes, Etc.

Eye Bolt Bending Feature forms neat smooth Eye Bolts, “S” shapes, “U” shapes, etc., of round or square stock up to 5/8″, cold. By using a wider Bending Dog and longer Forming Pin, flat stock up to 1-1/2″ in width can be handled. With standard equipment, Eyes and “U’s” can be bent with 1/2″, 5/8″, 3/4″, 7/8″ and 1″ inside openings. Special bushings for bending larger than 1″ eyes are available. Eyes 1-1/2″ or 2″ I.D. can be bent easily on 3/4″ stock. (Figure 2)

Back to top

Bending angles, offsets, etc. of heavy cold stock

Bending Angles, Offsets, Etc., of Heavy Cold Stock

Bends Angles, Irregular Shapes, Offsets, etc., of round or square stock up to 1-1/4″, or of flat stock up to 4-1/2″ x 1/2″. Gauges are provided for accurately locating the point of the bend and for gauging the degree of the angle desired. Illustration shows apiece of 2-1/2″ x 3/8″ stock being bent to a right angle. (Figure 3)

Back to top

Bending heavy cold U shapes

Bending Heavy Cold “U” Shapes

Bends “U” Shapes of 1-1/4″ round or square stock, or of 4-1/2″ flat stock, cold. Self-locking Cam Shaped Dies for bending “U”s of 1-3/4″, 2″ and 2-1/4″ inside spread are furnished with General Purpose Dies. These Dies can be built up to any larger size desired by simply bending a piece of flat stock around them. Illustration shows a “U” bolt being bent. (Figure 4)

Back to top

Bending sharp square bends on wide flat stock

Bending Sharp Square Bends on Wide Flat Stock

Bends Sharp Bends to a right angle or less on 4-1/2″ x 1/4″ flat stock, cold. This feature of the bender is used where a real sharp corner bend is required. It can be used for making sharp offsets, stake pockets, sharp cornered “U” clips, etc. Illustration shows a piece of flat stock inserted ready for bending. (Figure 5)

Back to top

Bending rings and coils

Bending Rings and Coils

Rings and continuous Coils of any desired diameter can be formed as shown in the illustration. The Forming ring may be a short piece of pipe of the right diameter or a 20B1 Bushing can be purchased from our Parts Catalog. The stock is fed along a distance of 1″ or 2″ after each pull of the hand lever. (Figure 6)

Back to top